Massive mirrors multiply the sense of house in rooms and add gentle to a darkish room. But massive mirrors or mirrors with elaborate frames are also inherently heavy. Whenever you cling a heavy mirror, it’s good to get it proper the primary time. Whereas different objects may maintain minimal harm in the event that they by chance drop, most mirrors will shatter and trigger an enormous mess if hung improperly.
What to Know About Hanging Heavy Mirrors
Mirrors are heavy as a result of mirrors are product of glass; any framework solely provides to the general weight. Most wall programs are constructed with vertical wall studs positioned each 16 inches on-center, with 1/2-inch drywall laid throughout the studs and held in place with drywall screws or nails.
To hold a heavy mirror on a wooden stud wall system, it’s all the time greatest to establish the placement of a number of studs behind the drywall and to drive the supporting fastener into these studs. Mirrors and footage are typically hung immediately from drywall however that is an inferior technique which will consequence within the fastener pulling out of the wall.
Grasp heavy mirrors both with screws and hanging wire or with steel cleats:
Screws and Hanging Wire
Heavy mirrors which have a steel wire will be held on wooden wall programs with one or two screws pushed into wall studs. If potential, make sure you use two screws. Buy solely braided chrome steel wire meant for hanging mirrors and footage.
Steel Cleats
Steel cleats are a stronger different to the wire-and-screws technique of hanging heavy mirrors. A steel strip is put in on the again of the mirror, with an interlocking cleat put in on the wall. Set up have to be exact because you do must make it possible for the wall cleat is precisely degree because it can’t be adjusted.
If you happen to want to double-check the energy of your wall fastener, buy a digital hanging scale (not a bathroom scale), cling the hook on the fastener, then manually pull the dimensions to the load of the mirror or extra.
Don’t use drywall screws as supporting fasteners since they’re brittle and should snap.
| Weight of Mirror With Wooden Body | |
|---|---|
| Dimensions (H/W) | Weight |
| 24 inches by 36 inches | 14 kilos |
| 24 inches by 48 inches | 19 kilos |
| 30 inches by 40 inches | 20 kilos |
| 24 inches by 60 inches | 24 kilos |
| 30 inches by 48 inches | 24 kilos |
| 36 inches by 48 inches | 30 kilos |
| 60 inches by 48 inches | 48 kilos |
| 72 inches by 48 inches | 60 kilos |
What You will Want
Gear / Instruments
- Cordless drill
- Drill bit set and drivers
- Stud finder
- Laser degree or bubble degree
- Tape measure
Supplies
- Mirror
- Chrome steel hanging wire
- Screws
- Drywall anchors (elective)
Directions
Utilizing Screws and Wire to Grasp a Mirror on Partitions
-
Determine the Studs’ Positions
Use the stud finder to find the positions of the studs close to your meant set up space. Mark the positions with the pencil. Normally, studs needs to be positioned each 16 inches, on-center.
![Stud finder placed against wall to identify positions]()
-
Mark Vertical Location
With the pencil, mark the vertical location of the heavy mirror. Understand that the highest fringe of the mirror will typically be 2 inches to 4 inches larger than the marks, so take that into consideration.
![Pencil making vertical location mark to place heavy mirror on wall]()
-
Decide Degree
Solid a laser degree line throughout the 2 marks and alter the marks in order that they’re degree.
![Laser level shining across wall to mark adjustments]()
-
Drive the Fastener Screws
With the cordless drill, drive two fastener screws on the adjoining studs. The heads of the screws ought to protrude about 1/4-inch.
![Fastener screws inserted into wall with cordless drill]()
-
Grasp the Mirror
Drape the mirror’s chrome steel hanging wire throughout the 2 fastening screws and let the mirror cling. Alter the extent by sliding one aspect of the mirror both up or down.
![Hanging wire attached to back of heavy mirror being placed on fastener screw]()
Utilizing Cleats to Grasp a Heavy Mirror on Partitions
-
Decide Degree
Use the stud finder to strike a degree line the place you need the cleat to run. Be exact about this, since cleats don’t permit for re-adjustment in the best way that the wire-and-screws technique does.
![Laser level shining across wall with pencil marking mirror locations]()
-
Screw the Cleat to the Wall
If in case you have a 16-inch or longer cleat, it will probably span from one stud to an adjoining stud. If the cleat is shorter than 16 inches, screw the middle gap to a stud and screw the 2 finish holes into drywall anchors.
![Metal cleat screwed on to wall with cordless drill and drywall anchors]()
-
Screw the Cleat to the Again of the Mirror
Screw the opposite cleat into the highest of the body on the again aspect. Make sure you maintain the cleat parallel with the highest of the body.
![Metal cleat screwed into back of heavy mirror with cordless drill]()
-
Connect the Mirror to the Wall
Connect the mirror by sliding the mirror cleat over the wall cleat. The mirror ought to relaxation firmly in place.
![Heavy gold mirror attached to wall cleats for hanging]()
When to Name a Skilled
For vintage mirrors, overly heavy mirrors, some masonry partitions, or for those who merely don’t really feel comfy hanging a heavy mirror, name a handyman service. This primary mission ought to take lower than an hour for many mirrors and wall programs, and a few half-hour further for masonry partitions.
